Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
We've uncovered this post pertaining to A Step-by-Step Guide to Installing a Bathtub below on the net and figured it made sense to write about it with you on this page.
Mounting a bath tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging job. If the old tub is conveniently easily accessible, the task can relocate quickly; if you have to open a wall to eliminate the old tub as well as position the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as are comfortable attempting it. Rather than working with a professional to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might require an expert plumber to make tube links.
This article will certainly aid you set up a new bath tub in your restroom if you have currently acquired a new bathtub as well as don't require to transform the arrangement of your previous water supply pipes.
Your devices and product list ought to consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Secure the faucet in position with the producer given backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former kind ought to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the producer's instruction manual. Tiling and also securing around the bathtub should wait up until the bath tub has been made use of at least when as this will certainly resolve it right into its final position.
Planning for the Installation
To start with, the supporting framework supplied with the bathroom should be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible tap adapters to the bottom of both faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently offered on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads about Tools You Need to Install a New Bathtub , I think sharing that piece of content was really useful. So long as you appreciated our blog posting kindly don't forget to pass it around. Thank you so much for going through it.
Guaranteed satisfaction offered. Report this page